Bullet heads

ScottPScottP Senior MemberPosts: 480 Senior Member
Most of the instructions I've seen for bullet-head flies start with the body and work towards the front. I've always had problems attaching the hair for the head and getting it to spin properly with the stub ends of the body and wing getting in the way, so I decided to reverse the process and tie the hair for head in first, letting it protrude out over the front of the fly while I tie in the rest:

a little thread to get things started (UTC 140 works great)
IMG_9594.jpg

a good hunk of hair (I like elk for the head but deer's fine, too) about shank length; you really want to use more hair than you think you need, which is somewhat counter-intuitive
IMG_9596.jpg

trim the butts, a couple soft loops and then pull firmly, letting the hair spin around the shank
IMG_9597.jpg

like so
IMG_9601.jpg

trim the butts (optional, but makes for a neater fly)
IMG_9603.jpg



The hair doesn't get in my way and I find it provides a nice base to attach the body and wing.


IMG_9606.jpg

a drop of Crazy Glue helps secure everything here
IMG_9609.jpg

add underwing (landscape fabric)
IMG_9613.jpg

add overwing
IMG_9618.jpg

push the head hair back over the fly; a finger works fine (guess those bullet-head tools would, too). Sinch it all down with a few firm wraps, add legs, a little Sally Hansen, trim out the bottom and Bob's your uncle
IMG_9621.jpg

They're a little putzy at first (mostly proportions, amounts and thread tension), but not hard and I got the hang of it after a few flies. Cool thing about the extended foam bodies is they're simple, you can make a bunch up ahead of time, bag them up and use as needed.


Regards,
Scott
They say the times are changing but I just don't know

Replies

  • ScottPScottP Senior Member Posts: 480 Senior Member
    Here's the back half:

    Charlie Craven has a great tutorial http://www.charliesflyboxinc.com/flybox/details.cfm?parentID=76 for the Rogue Stone which is what this is supposed to be with some modifications. You can do it by hand, like Barrett Christiansen does in this nice video for the Morrish October Caddis http://oregonflyfishingblog.com/2008/09/26/fly-tying-video-morrish-october-caddis/
    or place a needle in a vise (gives me a chance to break out the old Regal).

    IMG_9629.jpg

    push the foam strip onto the needle and then attach the tying thread (like I said previously, UTC 140 works great)

    IMG_9635.jpg

    squeeze the foam, and adjust to where you want the first body segment

    IMG_9636.jpg

    couple fairly firm thread loops around the foam (but not too firm or the thread will cut)

    IMG_9638.jpg

    then "split the uprights", move the thread between the foam "fingers" and up the needle to where you want the next segment

    IMG_9641.jpg

    repeat

    IMG_9642.jpg

    and again

    IMG_9643.jpg

    tie off with a couple half-hitches, slide the body off the needle

    IMG_9647.jpg

    trim the back end and front, brush a little Sally Hansen on the thread wraps and you're ready to go (excuse the mortar on my fingers, I'm doing this while laying tile in my bathroom)

    IMG_9651.jpg

    You can go production mode and make a bunch of these bodies ahead of time (no need to carry 2 vises or go back-and-forth between needle and hook in 1 vise).

    Regards,
    Scott
    They say the times are changing but I just don't know
  • ScottPScottP Senior Member Posts: 480 Senior Member
    Found one of those foam kneeler pads at Home Depot in a nice olive color

    IMG_9656.jpg


    It'd pass for a skwala, but it's a long way from spring now and there's a river in YNP that had some olive hoppers a couple years ago (and I didn't); it will be interesting to see if they're still there. Stuff is "softer" than craft foam, very easy to cut and work with. If it gets chewed up, that's a good thing; that's why they sell hooks in packs of 100.

    Regards,
    Scott
    They say the times are changing but I just don't know

Leave a Comment

BoldItalicStrikethroughOrdered listUnordered list
Emoji
Image
Align leftAlign centerAlign rightToggle HTML viewToggle full pageToggle lights
Drop image/file